柴达木盆地三湖坳陷横波勘探中的低幅异常消除技术

近年来,在柴达木盆地三湖坳陷开展了横波地震勘探,但是由于该区低幅度构造发育,横波静校正引起的"低幅"异常与上述低幅度构造相互混杂,难以区分。为此,针对该区横波表层调查难以控制表层横波速度模型的变化、横波近偏移距初至污染严重、横波折射层发育导致高速界面难以确定等问题,首先采用曲线拟合技术预测污染区横波初至时间确保初至完整性,然后采用面波模型与多层折射分层联合约束反演横波表层速度,最后通过基于速度谱分析的层位匹配建模技术确定合理的横波速度界面,形成了横波表层"低幅"异常消除技术,并进行了现场应用及效果评价。研究结果表明:①曲线拟合技术可以弥补近道污染区横波初至空白,保证层析反演模型的完整性;②基于瑞雷波的频散特性反演建模可以为确定该区浅层横波速度提供可靠的资料,提高浅层模型精度;③面波模型与多层折射分层联合约束反演能够更准确的反演该区表层横波速度场,较好地建立横波速度模型,消除横波剖面上"低幅"异常现象。结论认为,所形成的横波地震勘探低幅异常消除技术消除了横波静校正引起的"低幅"异常现象,提高了横波地震资料的成像品质。     

废脱硫剂在铁矿烧结中的应用

钢厂煤气脱硫工序排放的废脱硫剂是一种难以利用的有害固体废弃物，含一定量的铁及较高的钙和硫等元素。对废脱硫剂配入铁矿粉中进行了烧结杯的试验研究，结果表明，当废脱硫剂配比超过01%后，随着废脱硫剂配比的升高，烧结矿转鼓强度下降，利用系数下降，烧结烟气中SO2与NOx浓度增加，烧结矿的还原度有所下降，但烧结矿的低温还原粉化性能有所改善。烧结矿的矿相研究发现，废脱硫剂配比偏大时，磁铁矿体积分数增大，铁酸钙体积分数减少，并由针状结构向柱状、板状演变，烧结矿的气孔率上升。主要原因在于其粒度偏粗，含硫高，不利于成矿。当废脱硫剂粒度为-63mm及其配比控制在01%时，烧结矿的产量和质量有所改善，烟气中SO2、NOx较基准试验变化不大。工业试验表明，在烧结混匀矿中配入废脱硫剂配比小于012%时，烧结矿产量和质量没有明显变化，烧结烟气脱硫脱硝效果也没有受到影响。废脱硫剂掺入铁矿中进行烧结是一种资源化利用的有效方法，不仅解决了有害固体废弃物对环境的影响，而且使二次资源得到综合利用。     

Wire electrical discharge machinable SiC with GNPs and GO as the electrically conducting filler

SiC based composites filled with graphene nano-platelets (GNPs) or graphene oxide (GO) prepared by rapid hot-pressing exhibit sufficient electrical conductivity for their machinability by wire electro-discharge machining (WEDM). Composites microstructure anisotropy caused by graphene alignment as a consequence of rapid hot pressing was confirmed by measuring of electrical conductivity and thermal diffusivity. Electrical conductivity increased significantly with increased weight fraction of graphene in both measured directions. Highest value of 2031 S/m was obtained for composites with 15 wt. % of GNPs in parallel direction and only 1246 S/m in perpendicular direction to aligned GNPs. Thermal diffusivity is 63.3 mm²/s in parallel and only 23.3 mm²/s in perpendicular direction. The increase of the electrical conductivity has resulted in successful WEDM. The MRR was almost doubled when the filler concentration increased from 5 wt. % GNPs/GO to 15 wt. % GNPs. At the same time, the surface roughness decreased.     

车辆自组织网络中新型NP-CSMA随机多址协议研究分析

智能交通的出现使得车辆自组织网络受到越来越多的关注。车辆自组织网络的动态拓扑结构变化非常剧烈,这对网络的吞吐率、传输速率等性能提出了很高的要求。提出1种具有握手机制协议的自适应多通道双时钟NP-CSMA随机多址接入协议。该协议首先区分2种P-CSMA协议,握手机制成功解决了隐藏的终端问题,双时钟机制减少了平均空闲时间,多通道机制增加通道数量和划分用户优先级的同时提高了系统吞吐率,自适应机制能够使系统在高负载下保持稳定吞吐率。还对该协议的传输速率进行了分析,得出该协议的传输速率相对较高的结论。通过平均周期方法推导吞吐率和传输速率的计算公式,仿真结果与理论推导一致。     

Origin of the temperature stability of dielectric constant in CaCu3Ti4O12

The temperature and dc bias stability of the dielectric constant and loss tangent of CaCu₃Ti₄O₁₂ samples sintered under different oxygen atmospheres are discussed. The results suggest that the metal-oxygen vacancy related defects not only provide the charge carriers for the conduction (defect doping) but also contribute to the huge permittivity in the way of defect dipoles repositioning under charge carrier hopping. The charge localization in a specific copper-oxygen vacancy defect complex is the reason of the huge and stable permittivity and low dielectric loss in the middle temperature range, 90 K-200 K (20 Hz), while the implementation of the large barrier layer height needs a contribution by the titanium oxygen vacancy related trap charges in the grain boundaries, which also lead to a second permittivity stable range in a higher temperature range 200 K–300 K.     

正电子湮没研究Al、Nb共掺CaCu3Ti4O12陶瓷高介电常数机理

关于CaCu₃Ti₄O₁₂陶瓷的高介电常数机理，目前广泛接受的是非本征的内阻挡层电容模型。该模型认为在多晶中元素变价、缺陷和非化学计量比等导致的半导化晶粒被绝缘晶界层，即内阻挡层所包围。其中内阻挡层的厚度对材料的介电性能影响较大，而扫描电子显微镜（SEM）测试表明样品晶界呈稀烂的果酱状，SEM难以测量晶界区域绝缘内阻挡层厚度。本文采用正电子湮没技术表征其厚度，通过对CaCu₃Ti₄O₁₂陶瓷共掺不同浓度的Al、Nb（CaCu₃Ti_4-xAl_0.5xNb_0.5xO₁₂，x=0.2%、0.5%、5.0%）改变其晶粒和晶界的微观结构，研究CaCu₃Ti₄O₁₂陶瓷高介电常数机理。正电子湮没结果显示，掺杂样品符合多普勒展宽谱S参数的变化趋势与平均寿命的变化趋势一致。x=0.5%掺杂样品的介电常数最高，其平均寿命、S参数和湮没长寿命成分均最小，阻挡层最薄。实验结果验证了描述CaCu₃Ti₄O₁₂陶瓷高介电常数机理的内阻挡层电容模型的预测。     

基于改进雷达图的配电系统电能质量评估方法

本文针对配电系统电能质量综合评估存在的评估指标权重分配过于主观或客观的问题,提出一种基于改进雷达图法的配电系统电能质量评估方法。该方法利用最小偏差组合权重法计算各评估指标的最优组合权重。并在传统雷达图的基础上对各指标轴间夹角值的确定和特征向量的选取两方面做了进一步的改进。首先采用扇形区域取代原始的三角形区域,并利用最小偏差组合权重法计算各指标轴间夹角值。其次选择新的特征向量构造评估函数对配电系统电能质量进行综合评估。最后通过对某钢铁厂棒材变电站10kV配电系统电能质量进行综合评估,验证了该方法的可行性和合理性。较传统雷达图而言,改进雷达图法解决了传统雷达图法中各指标间信息共用以及评估结果不唯一的问题,使评估结果更加准确合理。     

Stabilizing temperature-capacitance dependence of (Sr,Pb, Bi)TiO3-Bi4Ti3O12 solutions for energy storage

(1-x)Sr_0.7Pb_0.15Bi_0.1TiO₃-xBi₄Ti₃O₁₂ ((1-x)SPBT-xBIT, x = 0-0.125) bulk ceramics were developed and calcined via the solid-state method, aimed at the application of pulsed power capacitors. The phase structures, temperature stability, hysteresis loop, and discharge properties were systematically investigated. Considering both the temperature stability and dielectric properties, 0.925SPBT-0.075BIT bulk ceramics with a capacitance variation satisfying the X7R specification were developed for pulsed power capacitors. The energy storage density was 0.252 J/cm³, and the ceramics showed high temperature stability at 80 kV/cm. The discharge current waveforms of the 0.925SPBT-0.075BIT ceramics were recorded. A high discharge power density of approximately 1.01 × 10⁸ W/kg with an 8 Ω load resistor and short discharge period of 84 ns were achieved at 50 kV/cm. The good temperature stability properties and high power density show that the 0.925SPBT-0.075BIT ceramics are well suited for pulsed power capacitors with a wide temperature range.     

Effects of temperature on creepage discharge characteristics in oil-impregnated pressboard insulation under combined AC–DC voltage

Due to the complexity of the valve side winding voltage of the converter transformer, the insulation characteristics of the oil-impregnated pressboard (OIP) of the converter transformer are different from those of the traditional AC transformer. The study on effect of temperature on the creeping discharge characteristics of OIP under combined AC–DC voltage is seriously inadequate. Therefore, this paper investigates the characteristics of OIP creepage discharge under combined AC–DC voltage and discusses the influence of temperature on creepage discharge characteristics under different temperatures from 70°C to 110 °C. The experimental results show that the partial discharge inception voltage and flashover voltage decrease with increasing temperature. The times of low amplitude discharge (LAD) decrease and amplitude of LAD increases. Simultaneously, the times of high amplitude discharge (HAD) gradually increase at each stage of creepage discharge with higher temperature. The analysis indicates that the charge carriers easily accumulate and quickly migrate directional movement along the electric field ahead of discharging. The residual charge carriers are more easily dissipated after discharging. The ‘hump’ region of LAD moves to the direction of higher discharge magnitude. The interval time between two continuous discharges is shortened obviously. The concentration of HAD accelerates the development of OIP insulation creepage discharge. The temperature had an accelerating effect on the development of discharge in the OIP under applying voltage.     

One-step synthesis of graphene supported platinum nanoparticles as electrocatalyst for PEM fuel cells

Here in, we describe an ultrafast, single-step microwave irradiation route (MW) to prepare graphene supported Pt nanoparticles, during which the small Pt nanoparticles are distributed uniformly on a reduced graphene oxide surface. This route provides evident advantages namely low cost, easiness, low time consuming and high yield in comparison to actual chemical methods to develop efficient Pt/rGO catalyst with Pt content close to state-of-the-art commercial composition. The structure and composition of prepared samples have been studied by specific techniques, while the electrocatalytic stability has been studied using ex-situ and in-situ measurements. High performance and electrochemically stable catalyst for PEM fuel cells was developed using the sample with highest loading and good dispersion. The fabricated Pt-rGO-based MEA was investigated for durability under fuel starvation in comparison with commercial Pt/C-based MEA. The electrocatalytic activity was investigated and the electrochemical response revealed the higher stability during accelerated degradation test under fuel starvation in comparison with commercial Pt/C. This study promotes the applicability of described preparation method to noble or transition metal nanoparticles embedded on graphene-based materials.